Class assignments are updated regularly for your convenience, to review periodically. If you have any questions please contact your instructor. In no means is this a replacement for attending classes or completing your work. If you have any questions about assignments listed here or others that may have been given be sure to contact your instructor.

FOURTH YEAR- Assignments

Fourth Year : May 27th through May 30th

Your hard work is finally paying off, and the end of your journey is at hand!

Section 9

62 Installing Eletrical Services II

63 Pools, Fountains, and Similar Locations

64 Understanding Emergency Building Installation Requirements

65 Over 600 Volt Installations

66 Remote Control, Signal and Power Limited Circuits

67 The 2005 NEC Part I

68 The 2005 NEC Part II

69 Determining Conductor Ampacity II

Section 10

70 Calculating Raceway Fill

71 Performing Box Size and Fill Calculations II

72 Introduction to Eletrical Load Calculations

73 Calculating the Parameters of Range Loads per the NEC

74 Calculating the Parameters of Residential Loads as per the NEC

75 Calculating the Parameters of Multifamily Dwelling Loads as per the NEC

76 TO BE DONE IN CLASS

THIRD YEAR- Assignments

Third Year A: May 19th through May 23rd

Third Year B: June 2nd through June 6th

Section 11

78 Introduction to Cable Trays

79 Cable Tray Applications

80 Cable Tray Systems and the NEC

81 Installation of Cable Tray Systems

82 Electric Welders

83 Phase Converters

Section 12

84 Hazardous Locations - Classifications

85 Hazardous Locations - Wiring Methods and Equipment

86 Special Occupancies

87 Electrical Equipment

88 Special Equipment

Extra Homework on Hazardous Locations & Motor Calculations

 

SECOND YEAR - Assignments

Second Year A: June 9th through June 13th

Second Year B: June 16th through June 20th

Section 10 - 2nd Year Material - Tranformers

Lesson 1 Understanding the Fundamental Design and Function of Transformers

Lesson 2 Learning How to Identify and Make Single-Phase Transformer Connections

Lesson 3 Becoming Familiar with Proper Transformer Installation Procedures

Lesson 4 Understanding the Foundational Principles of Three-Phase Systems

Lesson 5 Learning How to Identify and Connect Three-Phase Transformers

Section 11 - 3rd Year Material

54 Overcurrents: Overloads, Short-Circuits & Ground-Faults

55 Selection of Overcurent Protection Devices (OCPD) Ratings - V, A , IR

56 Types of OCPD - Circuit Breakers

57 Types of OCPD - Fuses

58 Branch Circuits, Feeders & Services

59 Conductor Tap Rule & Supervised Industrial Installations

Section 12 - 3rd Year Material

60 Transformer Protection - Article 450

61 Motor Branch Circuits - Article 430

62 Ground Fault Protection

63 Component Protection - NEC 110.10

64 Motor Overload and Single-Phasing Protection

65 Motor and Group Motor Protection and Devices - NEC Article 430

 

FIRST YEAR - Assignments

First Year A: May 5th through May 9th

First Year B: May12th through May 16th

 

Section 13

 

83 Developing NEC Code Book Skills

84 The Development of the NEC: The Table of Contents

85 The Arrangement of the NEC

86 The Structure of the NEC

87 The Language of the NEC

88 Codeology Fundamentals

89 Article 90 Introduction

90 Applying the NEC’s “GENERAL” Chapter

91 Applying the NEC’s “PLAN” Chapter

92 Applying the NEC’s “BUILD” Chapter

93 Applying the NEC’s “USE” Chapter

94 Interpreting the NEC’s “SPECIAL” Chapters

95 Applying the NEC’s “COMMUNICATION” Chapter and Tables in Chapter 9

 

Section 14

 

96 Reviewing the Applications of DC Theory

97 Comparing Direct Current to Alternating Current

98 Using Oscilloscopes to View AC Waveforms

99 Testing and Verifying Circuit Performance

100 Electronic circuit test instruments

101 An Introduction to Three-Phase Systems

102 Making Circuit Calculations for Basic Systems

103 Understanding How the DC Generator Works

104 Understanding the Design and Function of AC Generators

105 Becoming Familiar with AC Resistive Circuits

106 Getting Acquainted with Electrical Test Instruments

107 General use test instruments

108 Using and Understanding Multimeters

 

 
Next Step Design Solutions